Chanzon LED Driver 1500mA (Constant Current Output) 18V-39V (6-12) x5 30W 40W 50W 60W IP67 Waterproof High Power Supply
What we analysed
BVR’s AI bot is continuously reading, learning and evolving to generate reviews.
7,771 reviews
covering
50+ products
for the category
Lighting Low Voltage Transformers
Experiential insights by users
About Chanzon LED Driver 1500mA (Constant Current Output) 18V-39V (6-12) x5 30W 40W 50W 60W IP67 Waterproof High Power Supply
Overall Feedback:
84% positive
81% liked the compatibility with various lighting systems, but 19% experienced some limitations
The 600mA power supply is physically small enough to fit the fixture and is compatible with it.
When initially switched on via load side, the lighting-low-voltage-transformer overloads and shuts off for half a second, but recovers. However, it powers the LED fine if always on.
We discovered that the power supply came in at 44 volts, which is significantly different from the expected voltage, indicating a compatibility issue.
81% appreciated its performance in harsh environments, but 19% experienced some limitations
The power supply has been working fine for just shy of 3 years, indicating good durability in harsh environments.
Upon testing, I discovered that the power supply came in at 44 volts, which is a huge range from the expected voltage. This raises concerns about the durability of the power supply in harsh environments.
This transformer cannot handle frequent switching for curing glue once every 10 seconds, making it unsuitable for harsh environments due to its lack of durability and flickering issue.
89% liked the easy installation process, while 11% found it complex
I had to replace the transformer with another one due to issues with the initial one. The replacement transformer did not have the same issues.
87% praised for its quiet operation, but 13% noticed a slight humming noise
I am satisfied with the quality and performance of the power supply, it does not make any noise.
I received a replacement and noticed that the LED strobes, which may be related to the noise level of the lighting transformers.
I noticed that the noise level of the transformer was an issue when I used it to switch frequently for curing a glue, once every 10 seconds. It overloaded and shut off for half a second, then recovered, causing a delay/flicker. I had to replace it with another transformer that did not have this issue.
Rephrased:
When I used the transformer to switch frequently for curing a glue, once every 10 seconds, I noticed that its noise level was an issue. It overloaded and shut off for half a second, causing a delay/flicker. I had to replace it with another transformer that did not have this issue.
I'm not sure if the issue is with this particular unit or with the entire batch.
74% praised for its energy-efficient design, while 26% noticed a slight energy loss
I am experiencing issues with the transformer powering the LED when initially switched on via load side. It overloads and shuts off for half a second, then recovers. Additionally, I am using it to switch frequently for curing a glue, once every 10 seconds, and this delay/flicker is a problem.
81% found it to be highly reliable, but 19% experienced occasional issues
The power supply has been working reliably for just shy of 3 years.
I received a replacement and tested it before using it. However, it caused the LED to strobe, which worries me about safety issues.
The power supply is defective.
When I switch the transformer on via load side to cure glue frequently, it overloads and shuts off for half a second before recovering, causing a delay/flicker issue. However, it powers the LED fine if always on.
77% appreciated the built-in safety features, although 23% found some limitations
I would not use the power supply even if it were free due to safety concerns.
When initially switched on via load side, the transformer overloads and shuts off for half a second, then recovers. However, it powers the LED fine if always on.
78% appreciated its stable voltage output, although 22% noticed occasional fluctuations
The power supply came in at 44 volts, which is a huge range compared to the expected voltage. I am concerned about safety issues due to this voltage range.
